Versandkosten: 4,99 €
The environment of today’s automobiles present challenges for the installation of a performance car audio system when matched to a factory source unit. Less than ideal speaker locations coupled with an acoustically unfriendly environment can compromise the experience. Fortunately for audio enthusiasts, the new AudioControl DQ-61 delivers the processing power necessary to maximize the audio experience.
AudioControl engineers designed the DQ-61 to be an extraordinary processor, so subsequently it is equipped with a number of installer friendly features that simplify the OEM connection and calibration process.
User friendly Signal Delay controls allow the listeners the ability to align themselves between the left and right speakers plus seamlessly blend in the subwoofer to the listening environment. Discrete equalization controls provide listeners with powerful processing to properly “tune” their audio systems and enjoy truly amazing sound.
Designed for maximum sound quality and enhanced audio performance, the DQ-61 is the latest AudioControl processor to incorporate AccuBASS®. This patent pending process automatically corrects for the bass roll-off that is common with many factory-installed audio systems.
The DQ-61 has six speaker-level inputs. These inputs get their signals from the speaker-level outputs of your factory-installed source unit or amplifier. If your source unit has front, rear, and subwoofer signals, connect them to the corresponding inputs on your DQ-61. If your source unit only has front and rear signals, the AutoMode circuitry of the DQ-61 will route the Channel 2 signals to the Channel 3 (subwoofer) outputs.
Because of speaker placement limitations and the seating position in a car the driver of the vehicle is in an incorrect acoustic alignment with the speakers. The following steps will help set up delaying the appropriate speakers for just a few milliseconds, so the DQ-61 is able to allow the different signals to arrive at the same time putting the driver in perfect acoustical alignment.
Many cars can turn on the factory amplifier even if the source unit is off (Alarms, Cell phones, etc). To prevent this from turning your system on unexpectedly, you can bypass the GTO™ circuit by moving the GTO™ jumper, and using an applied 12-volts at the Remote In terminal. Using the jumper may result in some factory features not working fully. We ship them with the GTO™ in the “On” position.
Factory installed amplifiers and woofers are (unfortunately) not designed to reproduce bass at high volumes. Car manufacturers adapt to this by taking the bass out of the signal when you turn up the volume. AudioControl developed the patent pending AccuBASS™ circuit to restore bass. After a quick and easy one-time setting, the AccuBASS™ circuit takes over the bass just as the factory system rolls off. You get smooth, seamless, and rock solid bass response regardless of volume level.
When it comes to music, everyone has his or her own particular taste. Some people want pounding bass and crisp, blood curdling highs. Others may prefer a “flat” response (whatever the heck that is). At the end of the day, most people just want their system to sound balanced and “just like it did in the store” or similar to their buddy’s car. The following equalization guidelines should help you achieve your own personal audio nirvana.
The DQ-61 has the capability to combine together multiple (2, 4, or 6) input signals from the factory source unit into 2 channels. Some factory audio systems produce actively crossed over signals from the amplifier feeding signals to the tweeter, midrange, and woofer. The DQ-61 lets you take all of those signals and sum them together to get a high quality, full range, pre-amp signal.
Your DQ-61 is equipped with AudioControl’s unique AutoMode circuit input that allows for the Rear/Channel 2 input signal to automatically feed the Sub/Channel 3 outputs, when there is no signal present on Channel 3. This allows your DQ-61 to accept front and rear inputs channels and give you three output channels (Front, Rear, and Sub).
The ACR-3 is a multi-function remote that used for making the initial signal delay adjustments in the Set-Up mode and then providing level control over the Channel 3/Subwoofer output in the Normal mode. This allows you to balance the bass level with the rest of the system and then increase or decrease as needed. An additional feature of the ACR-3 dash remote is that it allows the signal processing of the DQ-61 (equalization, signal delay, and AccuBASS) to be switched in and out of the audio circuit. That means that you can hear the system with and without the processing and hear the difference that the tuning makes in the sound of your system.
The LC1i offers all of the features you'd expect in a high quality LOC without AccuBass or an ACR-1 dash mounted control knob port.
The LC2i Pro provides all the essential features needed when integrating aftermarket amplifiers with today's more complex factory sound systems.
The LC6i offers easy signal summing, 40 volts input handling and clean high to low level conversion.
When installing multi-channel amplifier systems into vehicles that will retain their factory radio, the LC6i offers a popular set of features to get the install done right and the vehicle sounding great... the first time.
The DQ-61 provides most of the popular features of a digital signal processor, but allows the installer to use traditional dials and switches instead of apps or software. With it's built-in EQ, time correction, signal summing, line driver, line output conversion and AccuBass features, the DQ-61 is an incredible value.
The LC8i offers 8 channels of easy signal summing, 40 volts input handling and clean high to low level conversion as well as an easy-to-use AUX input that can be controlled via the included ACR-2 dash mounted remote level control.
A digital signal processor is your solution. Our DM series (digital matrix) DSP's feature line output conversion, equalization, crossover, time alignment, signal summing, AccuBass and remote level control that can be assigned to any output. Our DM-Smart DSP app allows control of all features, runs on all popular platforms, and is among the easiest to use in the industry.
That's what makes the new LC-5.1300 an installer's dream. The combination of class-leading power levels, built-in line output converter with signal summing, flexible crossover section and unmatched warranty make the LC series of amplifiers like nothing else you've ever installed. This particular model boasts 1300 watts of RMS power and a streamlined interface for easier installation.
That's what the D series of amplifiers from AudioControl represent. If you're looking to install one amplifier that can truly "do it all", then the D-5.1300 is for you. With 1300 watts of RMS power, an onboard DSP, built-in LOC & signal summing, as well as a pair of RCA outputs from the DSP for future system expansion, there is truly nothing else quite like it.
| Technical data | Inputs
Outputs
Performance
Control
General
Weights & dimensions
|
|---|---|
| Scope of delivery |
|
| Brand | AudioControl |
| Product Type | High-Low Adapter |
| Eingangs-Kanäle | 6 |
| Ausgangs-Kanäle | 6 |
| Vorverstärker-Leistung | 7,5Vrms |
| EAN | 4047442070211 |
