Amplifier Wiring Kits & Racks

• Full specification cable - meets or exceeds AWG (American Wire Gauge) requirements
• 100% pure crystalline, oxygen-free copper (PC-OFC)
• Plug and play design for easy installation
• Fits Harley-Davidson® motorcycles 1998-2013
• Designed for use with the M5-800X4 and TM400X4ad amplifiers
• Y-adapters included in the amplifier installation kit support expansion of lower fairing, saddlebag or Tour-Pak® speakers
• Includes mounting brackets for Bat Wing and Shark Nose fairings
• Includes wiring harness for the rear speaker output for connecting rear speakers

The selected product is no longer available. You will find the successor in the shop under item number:

• FULL spec cable - meets or exceeds AWG (American Wire Gauge) requirements
• 100% Pure Crystal-Oxygen Free Copper (PC-OFC)
• Plug and Play design for easy installation
• Designed for use with 1998-Current Harley-Davidson® Motorcycles
• Designed for use with M5-800X4 amplifier
• Designed for use with TM400X4ad amplifier
• T-harness integration supports front/rear fader control (requires "Rockford Fosgate 2014+ All Bikes" flash)
• Includes mounting brackets for Bat Wing and Shark Nose fairings
• Includes amp output Y-adaptors for lower fairing and/or TourPak speakers
• Includes Boom!™ Audio bypass plugs for factory amplified systems
• Includes loop-thru harness for optional DSR1 signal processor
• NOTE: Your factory radio will need to be flashed

• Pre-cut, terminated and loomed power/ground & speaker wire harnesses
• Direct fit wiring and fusing with pre-terminated ends with Ferrule connectors
• Includes OEM connections for interfacing with 2014 and up models
• Suitable for Harley-Davidson® Street Glide™ / Electra Glide™ & Road Glide™ models
• 8GA OFC power and ground
• 16GA speaker wire
• 60A MAXI fuse

• Single or dual amp installation harness
• Oxygen-free copper wiring for better conductivity and performance
• 25mm² / 4GA OFC power and ground wires
• Distribution block to (2) 4GA power and ground wires
• 4ft Zip-tie for wire routing included
• 1998-2013 charge port T-harness, hardwired remote turn-on
• 2014-UP 2-pin plug in T-harness for accessory turn-on

• Suitable for Harley-Davidson® baggers 1998 through 2019
• 8 Gauge / 10mm² power and ground battery connections
• Waterproof fuse holder includes 2x 20A ATC fuses & Allen Key
• Heavy duty power quick disconnects
• Quality Shielded OFC RCAs with quick disconnects
• All cable runs are blacked out, loomed & terminated
• Stainless steel chrome plated wire inlets for both saddlebags included
• Speaker terminal assortment, amplifier power & speaker terminal forks included
• Zip ties included
• Amplifier remote turn-on integrated into quick disconnect harness
• No special tools needed for installation

• 2 channel amplifier wiring kit
• 6 & #39;of 8 gauge power / ground OFC wire with ring terminals
• Waterproof fuse holder with 2x 30 amp fuses
• RCA's are 9 & #39;long
• Front left / right speaker wires are 10 & # 39; long
• Left rear wire is 10 " #39;long including a 2.5&# 39; extension jumper for added length if needed. The extension can not be removed
• Right rear wire is 3 " #39;long
• Power / Ground, RCA & RCA & # 39; s all on quick disconnect connectors for easy removal of amplifier
• RCA and speaker wires are labeled for easy identification

• 2 channel amplifier wiring kit
• 6’ of 8 gauge power/ground OFC wire with ring terminals
• Waterproof fuse holder with 2x 30 amp fuses
• 10’ Long speaker wire
• RCA’s are 9’ long
• Power/Ground, speaker wires, and RCA’s all on quick disconnect connectors for easy removal of amplifier
• RCA’s and speaker wires individually labeled for easy identification

• Designed for motorcycles
• 1.8m red and black T-Spec OFC power and ground wire
• V8MANL fuse holder and 60 amp fuse protected by a black nylon braid
• Pre-terminated ring terminals make connections to the battery simple
• 2x 1.2m speaker cable OFC (1.5mm²) protected by automotive shrink & braided sleeving
• Incl. Velcro pad (10x15cm), holds all amplifiers without fans in the base securely in place

• Designed for motorcycles
• 1.8m red and black T-Spec OFC power and ground wire
• T-Spec V8MANL fuse holder with 30A fuse protected by black nylon braid
• Pre-assembled ring cable lugs make connection to the battery easy
• 2x 1.2m loudspeaker cable OFC (1.5mm²) protected by automotive heat-shrink and braided hose
• Includes 10×15cm microamp velcro strap to keep the amp securely in place